Mumbai is home to switchgear makers, panel builders, pharma companies and the head offices of many OEMs and EPC contractors. The busy industrial pockets of Andheri, Marol, Vikhroli and Bhandup alone keep a steady demand for transformers, chokes and reactors.
VA Electricals designs and manufactures buck boost transformers at its works in Bhosari, Pune. Every unit is built to your voltages and rating and tested in-house, then delivered by road to customers in Andheri MIDC, Marol, Vikhroli and across Mumbai.
Built for 230 V single-phase / 415 V three-phase, 50 Hz, with the buck or boost amount chosen to bring your supply to the equipment's rated voltage.
A buck boost transformer raises (boosts) or lowers (bucks) the supply voltage by a small amount so equipment receives the voltage it is designed for. Because it only handles the correction voltage, it is far smaller and more economical than a full isolation transformer for the same load.
For sites in Mumbai where the supply sits a little above or below what equipment is rated for, a buck boost transformer corrects the voltage economically, without a full-size transformer.
Lowers a high supply voltage to protect equipment rated for a lower voltage.
View product detailsRaises a low or sagging supply so motors and compressors run at rated voltage.
Designed around your measured supply range and load.
Switchgear and panel shops in Andheri MIDC, Marol and Vikhroli build MCC, PCC and automation panels for projects across India.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Pharma and speciality chemical companies headquartered in Mumbai run plants with heavy VFD and process-control loads.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Mumbai is India's largest data-centre hub, with server farms in Chandivali, Powai and the eastern suburbs.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
High-rise construction and MEP contractors need panels for lifts, pumps, HVAC and fire-fighting systems.
Typical use: Long cable runs and low-voltage sites in commercial buildings.
Large hospitals and diagnostic chains depend on clean, uninterrupted power for imaging and ICU equipment.
Typical use: Correcting voltage for imaging and laboratory equipment.
Electronics and power-electronics firms design UPS, inverter and control products for the national market.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Plants in Mumbai see summer heat in panel rooms, monsoon humidity and supply fluctuations. Share your duty cycle and ambient conditions, and we design the rating, insulation and construction to suit.
| Function | Buck (step-down) or boost (step-up) voltage correction |
|---|---|
| Rating | As per load and correction required |
| Supply | 230 V single-phase / 415 V three-phase, 50 Hz systems |
| Correction | Set to bring supply to equipment's rated voltage |
| Frequency | 50 Hz (Indian grid standard) |
| Construction | Open frame or enclosed |
| Compliance | CE marked under LVD 2014/35/EU (transformers up to 200 kVA); ISO 9001:2015 production |
| Routine tests | Ratio, no-load, insulation resistance, HV breakdown, winding resistance |
Orders for Mumbai are dispatched by road from our works in Bhosari, Pune, about 150 km away. Every consignment is packed to protect windings and terminals in transit. Being this close, deliveries are quick and our engineers are easy to reach for technical discussions or site visits.
Send your requirement
Of transformer design and manufacturing experience behind every unit.
ISO 9001:2015 quality system and CE conformity under the Low Voltage Directive.
Voltages, ratings, terminals and mounting made to match your design.
Production planned around your project schedule and delivery dates.
Yes. VA Electricals manufactures buck boost transformers at its works in Pune, India and supplies customers across Mumbai, including Andheri MIDC, Marol, Vikhroli, Bhandup, Kurla.
Yes. Units are built for the 230 V single-phase / 415 V three-phase, 50 Hz supply used in Mumbai, with the buck or boost amount chosen to bring your supply to the equipment's rated voltage.
When the supply only needs a small voltage correction and isolation is not required. A buck boost unit handles only the correction voltage, so it is smaller, lighter and lower in cost for the same load.
VA Electricals operates an ISO 9001:2015 certified quality management system and holds MSME ZED Bronze certification. Its products carry CE conformity under the Low Voltage Directive 2014/35/EU, covering transformers up to 200 kVA.
Dispatched by road from our Pune works, about 150 km away, packed to protect windings and terminals in transit.
Yes. Tell us the ambient temperature, duty cycle and supply conditions at your plant, and we design the rating, insulation and construction to suit.
Share your voltages, rating and quantity. Our engineers will send a technical offer for supply to Andheri MIDC, Marol, Vikhroli or anywhere in Mumbai.