Delhi NCR is North India's largest manufacturing and trading region. Okhla, Bawana and Narela in Delhi, the Noida and Greater Noida electronics belt, and the Gurugram-Manesar automotive corridor all buy transformers, chokes and reactors in volume.
VA Electricals designs and manufactures buck boost transformers at its works in Bhosari, Pune. Every unit is built to your voltages and rating and tested in-house, then delivered by road to customers in Okhla, Bawana, Narela and across Delhi NCR.
Built for 230 V single-phase / 415 V three-phase, 50 Hz, with the buck or boost amount chosen to bring your supply to the equipment's rated voltage.
A buck boost transformer raises (boosts) or lowers (bucks) the supply voltage by a small amount so equipment receives the voltage it is designed for. Because it only handles the correction voltage, it is far smaller and more economical than a full isolation transformer for the same load.
For sites in Delhi NCR where the supply sits a little above or below what equipment is rated for, a buck boost transformer corrects the voltage economically, without a full-size transformer.
Lowers a high supply voltage to protect equipment rated for a lower voltage.
View product detailsRaises a low or sagging supply so motors and compressors run at rated voltage.
Designed around your measured supply range and load.
Noida and Greater Noida host electronics, inverter and UPS manufacturers.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
The Gurugram-Manesar belt hosts car and two-wheeler plants and hundreds of suppliers.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Panel builders in Okhla, Bawana and Ghaziabad supply projects across North India.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Noida and Gurugram are fast-growing data-centre markets.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Metro, airport and commercial construction projects need MEP and control panels.
Typical use: Long cable runs and low-voltage sites in commercial buildings.
Large hospital chains and diagnostic centres rely on UPS and isolation transformers.
Typical use: Correcting voltage for imaging and laboratory equipment.
Plants in Delhi NCR see summer heat in panel rooms, monsoon humidity and supply fluctuations. Share your duty cycle and ambient conditions, and we design the rating, insulation and construction to suit.
| Function | Buck (step-down) or boost (step-up) voltage correction |
|---|---|
| Rating | As per load and correction required |
| Supply | 230 V single-phase / 415 V three-phase, 50 Hz systems |
| Correction | Set to bring supply to equipment's rated voltage |
| Frequency | 50 Hz (Indian grid standard) |
| Construction | Open frame or enclosed |
| Compliance | CE marked under LVD 2014/35/EU (transformers up to 200 kVA); ISO 9001:2015 production |
| Routine tests | Ratio, no-load, insulation resistance, HV breakdown, winding resistance |
Orders for Delhi NCR are dispatched by road from our works in Bhosari, Pune, about 1450 km away. Every consignment is packed to protect windings and terminals in transit. Consignments travel by road transport with dispatch details shared in advance, so your project or production schedule stays on track.
Send your requirement
Of transformer design and manufacturing experience behind every unit.
ISO 9001:2015 quality system and CE conformity under the Low Voltage Directive.
Voltages, ratings, terminals and mounting made to match your design.
Production planned around your project schedule and delivery dates.
Yes. VA Electricals manufactures buck boost transformers at its works in Pune, India and supplies customers across Delhi NCR, including Okhla, Bawana, Narela, Mayapuri, Wazirpur.
Yes. Units are built for the 230 V single-phase / 415 V three-phase, 50 Hz supply used in Delhi NCR, with the buck or boost amount chosen to bring your supply to the equipment's rated voltage.
When the supply only needs a small voltage correction and isolation is not required. A buck boost unit handles only the correction voltage, so it is smaller, lighter and lower in cost for the same load.
VA Electricals operates an ISO 9001:2015 certified quality management system and holds MSME ZED Bronze certification. Its products carry CE conformity under the Low Voltage Directive 2014/35/EU, covering transformers up to 200 kVA.
Dispatched by road from our Pune works, about 1450 km away, packed to protect windings and terminals in transit.
Yes. Tell us the ambient temperature, duty cycle and supply conditions at your plant, and we design the rating, insulation and construction to suit.
Share your voltages, rating and quantity. Our engineers will send a technical offer for supply to Okhla, Bawana, Narela or anywhere in Delhi NCR.