Surat combines one of the world's biggest textile and diamond industries with heavy industry at Hazira. Sachin and Pandesara GIDCs run thousands of looms and processing units, and the Ankleshwar-Bharuch chemical belt is close by.
VA Electricals designs and manufactures buck boost transformers at its works in Bhosari, Pune. Every unit is built to your voltages and rating and tested in-house, then delivered by road to customers in Sachin GIDC, Hazira, Pandesara GIDC and across Surat.
Built for 230 V single-phase / 415 V three-phase, 50 Hz, with the buck or boost amount chosen to bring your supply to the equipment's rated voltage.
A buck boost transformer raises (boosts) or lowers (bucks) the supply voltage by a small amount so equipment receives the voltage it is designed for. Because it only handles the correction voltage, it is far smaller and more economical than a full isolation transformer for the same load.
For sites in Surat where the supply sits a little above or below what equipment is rated for, a buck boost transformer corrects the voltage economically, without a full-size transformer.
Lowers a high supply voltage to protect equipment rated for a lower voltage.
View product detailsRaises a low or sagging supply so motors and compressors run at rated voltage.
Designed around your measured supply range and load.
Sachin, Pandesara and Palsana run thousands of water-jet looms, embroidery and processing machines.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Hazira hosts large steel, engineering and port-based industries.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
The Ankleshwar and Bharuch GIDCs are among India's largest chemical clusters.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Diamond cutting and polishing units use precision, electronically controlled machines.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Refinery, gas processing and LNG facilities operate along the Hazira coast.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Plastic and polymer processors run extrusion and moulding machines on VFDs.
Typical use: Bucking or boosting supply voltage by a small amount to match equipment.
Plants in Surat see summer heat in panel rooms, monsoon humidity and supply fluctuations. Share your duty cycle and ambient conditions, and we design the rating, insulation and construction to suit.
| Function | Buck (step-down) or boost (step-up) voltage correction |
|---|---|
| Rating | As per load and correction required |
| Supply | 230 V single-phase / 415 V three-phase, 50 Hz systems |
| Correction | Set to bring supply to equipment's rated voltage |
| Frequency | 50 Hz (Indian grid standard) |
| Construction | Open frame or enclosed |
| Compliance | CE marked under LVD 2014/35/EU (transformers up to 200 kVA); ISO 9001:2015 production |
| Routine tests | Ratio, no-load, insulation resistance, HV breakdown, winding resistance |
Orders for Surat are dispatched by road from our works in Bhosari, Pune, about 420 km away. Every consignment is packed to protect windings and terminals in transit. Consignments travel by road transport with dispatch details shared in advance, so your project or production schedule stays on track.
Send your requirement
Of transformer design and manufacturing experience behind every unit.
ISO 9001:2015 quality system and CE conformity under the Low Voltage Directive.
Voltages, ratings, terminals and mounting made to match your design.
Production planned around your project schedule and delivery dates.
Yes. VA Electricals manufactures buck boost transformers at its works in Pune, India and supplies customers across Surat, including Sachin GIDC, Hazira, Pandesara GIDC, Udhna, Kim.
Yes. Units are built for the 230 V single-phase / 415 V three-phase, 50 Hz supply used in Surat, with the buck or boost amount chosen to bring your supply to the equipment's rated voltage.
When the supply only needs a small voltage correction and isolation is not required. A buck boost unit handles only the correction voltage, so it is smaller, lighter and lower in cost for the same load.
VA Electricals operates an ISO 9001:2015 certified quality management system and holds MSME ZED Bronze certification. Its products carry CE conformity under the Low Voltage Directive 2014/35/EU, covering transformers up to 200 kVA.
Dispatched by road from our Pune works, about 420 km away, packed to protect windings and terminals in transit.
Yes. Tell us the ambient temperature, duty cycle and supply conditions at your plant, and we design the rating, insulation and construction to suit.
Share your voltages, rating and quantity. Our engineers will send a technical offer for supply to Sachin GIDC, Hazira, Pandesara GIDC or anywhere in Surat.